Phone Number

+8675529071623

Circuit Tester

CP201.8-inch Circuit Tester with Multimeter, Waveform & Activation

8–32 V input and 0–80 V DC testing, with polarity, continuity, ground checks and specified component activation. A 5 m main cable, overload protection and lighting support troubleshooting.

Product overview

The CP20 combines voltage measurement, polarity/ground checks, continuity and component activation in a handheld probe for use with vehicle wiring diagrams. Measurement and active power application are different operations: identify the circuit and component limits before selecting a function. Check supply, measurement range and output-current limits separately.

Key capabilities

Voltage, polarity and wiring checks

Check DC voltage and polarity, then use the auxiliary ground lead for continuity/ground checks and to help locate trailer-light, connector and short-circuit issues. Isolate circuits for continuity as instructed; continuity alone does not prove correct behavior under load.

Activate within rated conditions

Apply positive supply or ground to permitted components as instructed, up to 8 A. The 0–80 V measurement range is not an activation-output voltage rating; output depends on the connected supply and circuit conditions.

Working reach and protection

A 5 m main cable and lighting aid access. Overload protection requires investigation of a short, excessive load or connection issue after a trip; repeated trips are not a diagnostic substitute.

Six multimeter functions

Includes voltage, resistance, diode, continuity, polarity and frequency. Follow isolation requirements for resistance/continuity; max/min, frequency and duty cycle help compare signals.

Waveform display and hold

The waveform page shows voltage changes and related readings with display hold and rotation. It supports initial comparison of suitable signals, without claiming general-purpose scope bandwidth or CAN message decoding.

Suggested workflow

  1. Identify the circuit and tool limits — Check the wiring diagram, component rating, supply range and intended test; inspect leads and perform the prescribed self-test.

  2. Measure before deciding on activation — Check voltage, polarity and connections first. Activate only components approved for external power and do not energize unidentified circuits.

  3. Record and verify — Interpret readings and load behavior with the diagram, investigate abnormalities and restore/check connections after testing.

Frequently asked questions

Why do input, measurement and activation limits differ?

Input powers the tool, the measurement range specifies readable voltage, and activation limits govern output/load. They are not interchangeable; measurement limits do not define output voltage.

Can the activation switch be used on any terminal?

No. Verify terminal function, isolation and allowable voltage/current using service information. Activate only suitable components and do not activate during continuity tests.

Does overload protection prevent all damage from misuse?

No. Incorrect voltage, terminal selection or sensitive circuits may still be damaged. Protection assists correct operation; wiring and rated limits remain essential.

Product design

CP20 Product design

Documentation and support

View product documentation and contact technical support

Key features

8–32 V input and 0–80 V DC testing, with polarity, continuity, ground checks and specified component activation. A 5 m main cable, overload protection and lighting support troubleshooting.

Applications

CP20 circuit tester: 8–32 V supply, 0–80 V DC measurements and up to 8 A specified activation. View polarity, continuity and ground checks, specifications and FAQ.

Technical specifications

ItemSpecification or function
ModelCP20
Input supply8–32 V
DC test voltage0–80 V
Operating current80 mA
Activation current limit8 A
Main cable5 m
Display1.8-inch TFT color display
Measurement/wiring functionsVoltage, polarity, continuity, ground and short-circuit assistance
Component activationPositive supply or ground per instructions, permitted components only
ProtectionReverse-connection and overload safeguards; conditions per manual
Lighting and alertsLED lighting and buzzer alerts
Nominal vehicle systems12 / 24 V
Multimeter functionsVoltage, resistance, diode, continuity, polarity and frequency
Continuity thresholdBuzzer at R < 100 Ω; silent at R ≥ 100 Ω
Waveform and additional readingsVoltage waveform, max/min voltage, frequency and duty cycle
Display controlsDisplay hold and 180° rotation per device controls
CAN-related checkPolarity check, not CAN message decoding
Languages and self-test12 languages; LCD, LED and buzzer self-test
Body dimensions180 × 45 × 24 mm
Operating temperature0–60°C
Storage temperature−40–70°C
ProbeDetachable

Supply, measurement and activation have different limits. Verify circuit function and component ratings before use; protection does not replace correct wiring.

CP20 1.8-inch Circuit Tester with Multimeter, Waveform & Activation